Hello everyone! In this post, I’m sharing details on how I made my latest pixel art creation: an 8-bit Black Mage from Final Fantasy!

This is a new style of pixel art for me. It was largely inspired by abstract pieces I’ve spotted online.

RELATED POSTS:

• 8-bit Goomba (Super Mario Bros.)
• 8-bit End Grain Goomba (Super Mario Bros.)
• 8-bit Link (The Legend of Zelda)

(For sneak peeks on upcoming projects follow me on Instagram and for more DIY project tutorials check out my project gallery!)

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.

Let’s get started on the build!

Tools and Supplies

The following items are some of the tools and supplies I gathered to create the 8-bit Black Mage.

Tools

• Table saw (or bandsaw)
• GRR-RIPPER (Makes using the table saw less scary and safer)
• FF DOT: The Pixel Art of Final Fantasy

Supplies

• 2×4 scraps
• 1/4″ plywood
• Stains
• Acrylic Paint
• Gloss Spray Paint
• Paint brush
• Sand paper
• Wood Glue

Watch the Video Tutorial

Click play and watch the video tutorial below. For more woodworking videos, CLICK HERE to subscribe to my YouTube channel.

Continue reading for the written tutorial.

How to make an 8-bit Black Mage

This project is a great way to make a dent in your scrap wood pile. I used 2×4 off cuts to create the Black Mage.

Step 1: Rip 2x4s into 3/4″ square rods

I started off by ripping off the rounded corner of the 2×4 scraps before ripping the boards down into 3/4″ square rods.

Step 2: Crosscut the square rods into 1″ – 1 1/2″ pieces

Next up crosscut the square rods into pieces varying in heights of 1″ to 1 1/2″. Alternate between different bevels as you cut the pieces.

Step 3: Color the pixels

Group the wooden pieces into 4 different piles: one for each color in the black mage.

• Black: 194 pieces
• Gold: 43 pieces
• Tan: 40 pieces
• Aqua: 107 pieces

I originally used stain colors, but went back and painted the gold and tan pieces with acrylic paint because I wasn’t able to get get a good color match.

Step 4: Assemble the Black Mage

Next up, glue together the pixels. I used an image from the book FF DOT: The Pixel Art of Final Fantasy as my reference.

I also used two pieces of scrap plywood to create a jig for keeping the pixels square.

Once the glue drys, spray the Black Mage with a few coats of gloss spray paint and enjoy!

8-Bit Final Fantasy Black Mage

I wasn’t too pleased with my job of gluing, but overall I’m really happy with how it turned out.

Let’s be friends!

• Instagram: @handmadewithashley
• Facebook: @handmadewithashley
• Twitter: @handmadewithash
• YouTube: @handmadewithashley
• Pinterest: @handmadewithashley
• Instructables: @handmadewithashley

The post 8-Bit Final Fantasy Black Mage |Wooden Pixel Art appeared first on Handmade with Ashley.

Hello everyone, in this tutorial I’m sharing how to make your very own Pikachu resin pendants. This is a pretty simple DIY project where the most tedious and critical step is the paint job. You can use the finished pendants on a necklace or glue a magnet to the backside to hang documents on a refrigerator.

(For sneak peeks on upcoming projects follow me on Instagram and for more DIY project tutorials subscribe to my YouTube channel!)

I’ve been a fan of Pokemon for many years. As a child, I always look forward to watching a new episode of the TV show during Saturday morning cartoons. I also spent many hours playing Pokemon Yellow on the Gameboy Pocket trying to collect all 150 Pokemon. I have so many fond memories of the series and was super excited to see the Pokemon Indigo League available on Netflix. I started re-watching the show with my son and felt motivated to create some Pokemon themed projects.

RELATED POST: How to make a Darth Vader resin necklace.

Let’s get started with the project!

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.  This helps keep the content on the site free and I appreciate the support! :o)

What You’ll Need

To make the Pikachu pendant you’ll need the following items:

• Pikachu Ice Mold
• Casting Resin
• Resin Mixing Cups
• Resin Stirring Sticks
• Disposable Gloves
• Golden Sunset Spray Paint
• Gloss Spray
• Red, Black, and White Acrylic Craft Paints
• Miniature Paint Brushes
• A needle
• Sandpaper

NOTE: As of writing this tutorial, I noticed the ice mold that I purchased is not currently in stock. Here’s an alternative silicone Pikachu mold.

How to make Pikachu Resin Pendants

Here’s how to make the Pikachu resin pendants in three steps!

Step 1: Mix resin and carefully pour it into the mold

IMPORTANT NOTE: Before starting make sure you handle resin with great care (wear gloves + work in a well ventilated area) and follow the manufacture’s instructions.

I used Alumilite’s Amazing Casting Resin for this project. This resin cures white in 10 minutes. This doesn’t give you very much time to work with.

Once you pour the resin in the mold try to remove any air bubbles you might see. I used a toothpick to remove any that were stuck on the features of Pikachu’s face. After the resin cures, carefully remove the Pokemon from the mold.

Step 2: Spray paint the Pokemon yellow

Prior to painting, sand the backside of the pendants. This step may not be necessary for you, but if you notice rough edges and an even bottom, level it out with a little sanding on a flat surface.

Grab a can of Golden Sunset spray paint and cover the top and bottom sides of Pikachu with a layer of the golden paint.

Step 3: Paint Pikachu’s face

Once the base coat is dried, it’s time to paint the features of Pikachu’s face. This is the most difficult step of the project. It’s important that you take your time as the better the paint job, the better the project with look once it’s complete.

Paint the tips of Pikachu’s ears black. I needed two layers of paint here.

A paint brush is too large for painting Pikachu’s eyes, eyelids and nose. Grab a needle or something with a sharp point to fill in those areas. Just dip the tip into paint and dab the needle into those sections of Pikachu’s face. You’ll need a steady hand and a little patience.

Easily the most frustrating step in the whole project.

Paint Pikachu’s cheeks and mouth with red paint and the light of his eye with white paint.

Allow the paint to dry before spraying the pendants with a clear gloss spray.

DIY Pikachu Resin Charm

Thanks for checking out my project. I hope you’ve been inspired to go make a set of Pokemon pendants too.

FIND ME ONLINE!

• Instagram: @handmadewithashley
• Facebook: @handmadewithashley
• Twitter: @handmadewithash
• YouTube: @handmadewithashley
• Pinterest: @handmadewithashley
• Instructables: @handmadewithashley

The post DIY Pikachu Resin Pendant appeared first on Handmade with Ashley.

Hello, everyone in this post I’m sharing details on how I made an 8-bit R2-D2 from Star Wars. I made R2-D2 using the same technique I used to create a few of my other pixel art creations like 8-bit Link, Goomba, Lakitu, Spiny, Koopa Troopa and Blooper.

(For sneak peeks on upcoming projects follow me on Instagram and for more DIY project tutorials subscribe to my YouTube channel!)

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.  This helps keep the content on the site free and I appreciate the support! :o)

Tools and Supplies

The following items are some of the tools and supplies I gathered to make 8-bit R2-D2:

TOOLS

• Jigsaw or a bandsaw
• Orbital Sander
• Router with 60 degree v-groove bit
• Clamp edge guide
• Kreg Mobile Project Center
• Ruler

SUPPLIES

• 2′ x 2′ plywood – 1/2″ thick
• Acrylic craft paints (white, black, blue and red)
• Primer spray paint
• Clear coat
• Sand paper

WATCH THE VIDEO TUTORIAL

Click play and watch the video tutorial below.  The video shows how I made pixel Link, but the general steps remain the same for pixel R2-D2. For more woodworking videos, CLICK HERE to subscribe to my YouTube channel.

Continue reading for the written tutorial.

How to make R2-D2

Here’s how to make R2-D2 in 5 easy steps.

Step 1: Draw a grid on a piece of plywood.

Use a ruler to mark grid lines space 0.75″ apart.

Step 2: Use a router and route a v groove along the grid lines

Install a v-groove router bit and route along the grid lines. Use a clamp edge guide to ensure straight lines

Step 3: Cut out the silhouette of R2-D2’s shape

I followed a pixel grid for R2-D2 that I found online. Here’s the source of my image.

Trace out the silhouette of R2-D2 and then cut out the R2-D2’s shape with a jigsaw (or use a bandsaw).

Step 4: Sand and prep the surface for paint

Sand between the grooves and sand the surface of R2-D2.  I used scrap piece of wood to support the sandpaper as I sanded between the grooves.

Step 5: Paint the pixels

Paint each pixel on R2-D2. Painting between the grooves is a little tricky. Use painters tape to maintain clean lines. I was impatient and used paint brushes for painting miniatures to paint in the crevices. 

If necessary, apply multiple layers of paint. Once the paint is dried, protect the finish with a clear coat.

8-Bit R2-D2

Install some hanging hardware and enjoy!

FIND ME ONLINE!

• Instagram: @handmadewithashley
• Facebook: @handmadewithashley
• Twitter: @handmadewithash
• YouTube: @handmadewithashley
• Pinterest: @handmadewithashley
• Instructables: @handmadewithashley

What do you think of the pixel R2D2? Leave a comment below!

The post 8-Bit Star Wars R2-D2 Pixel Wall Art Tutorial appeared first on Handmade with Ashley.

Hello everyone, today I’m sharing how to make 8-bit pixel Spiny from the NES version of Super Mario Bros. I followed the same technique I used to create 8-bit pixel Link from the original The Legend of Zelda game.

CLICK HERE to view more geeky and nerdy DIY projects.

Related Posts:

• 8-bit Goomba (Super Mario Bros.)
• 8-bit End Grain Goomba (Super Mario Bros.)
• 8-bit Link (The Legend of Zelda)
• 8-bit Cheep Cheep (Super Mario Bros.)
• 8-bit Mario (Super Mario Bros.)

(For sneak peeks on upcoming projects follow me on Instagram!)

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.  This helps keep the content on the site free and I appreciate the support! :o)

TOOLS AND SUPPLIES

I used the following tools and supplies to create pixel Spiny:

TOOLS

• Jigsaw or a bandsaw
• Orbital Sander
• Router with 60 degree v-groove bit
• Clamp edge guide
• Kreg Mobile Project Center
• Ruler

SUPPLIES

• 2′ x 2′ plywood – 1/2″ thick
• Acrylic craft paints ( spice tan, fire red and white)
• Primer spray paint
• Clear coat
• Sand paper

WATCH THE VIDEO TUTORIAL

Click play and watch the video tutorial below.  The video shows how I made pixel Link, but the general steps remain the same for pixel Spiny. For more woodworking videos, CLICK HERE to subscribe to my YouTube channel.

Continue reading for the written tutorial.

HOW TO MAKE 8-BIT PIXEL
SPINY IN 5 EASY STEPS

1. Draw 1.5″ grid lines
2. Route along the grid lines
3. Cut out Spiny’s silhouette
4. Prep Pixel Spiny for painting
5. Paint 8-bit Spiny

STEP 1: DRAW 1.5″ GRID LINES

Use a ruler to mark grid lines space 0.75″ apart.

STEP 2: ROUTE ALONG THE GRID LINES

Install a v-groove router bit and route along the grid lines. Use a clamp edge guide to ensure straight lines.

STEP 3: CUT OUT SPINY’S SILHOUETTE

Trace out the silhouette of Spiny and then cut out the Spiny’s shape with a jigsaw (or use a bandsaw).

STEP 4: PREP PIXEL SPINY FOR PAINTING

Sand between the grooves and sand the surface of Spiny.  I used scrap piece of wood to support the sandpaper as I sanded between the grooves.

STEP 5: PAINT PIXEL SPINY

Paint each pixel on Spiny. Painting between the grooves is a little tricky. Use painters tape to maintain clean lines. I was impatient and used paint brushes for painting miniatures to paint in the crevices.
If necessary, apply multiple layers of paint. Once the paint is dried, protect the finish with a clear coat.

The nice thing about working on Spiny at the same time is the characters use the exact same colors.

DIY 8-BIT PIXEL SPINY

I am really happy with how the 8-bit Super Mario characters turned out. Next up: Giant Goomba!

8-bit Spiny looks great with Lakitu, Koopa Troopa and Goomba on the garage door!

PIN IT!

FOLLOW ME on Pinterest.

The post 8-Bit Spiny | Super Mario Bros Pixel Wall Art Tutorial appeared first on Handmade with Ashley.

Hello everyone, today I’m sharing how to make 8-bit pixel Lakitu and Koopa Troopa from the NES version of Super Mario Bros. I followed the same technique I used to create 8-bit pixel Link from the original The Legend of Zelda game.

CLICK HERE to view more geeky and nerdy DIY projects.

Related Posts:

• 8-bit Goomba (Super Mario Bros.)
• 8-bit End Grain Goomba (Super Mario Bros.)
• 8-bit Link (The Legend of Zelda)
• 8-bit Cheep Cheep (Super Mario Bros.)
• 8-bit Mario (Super Mario Bros.)

(For sneak peeks on upcoming projects follow me on Instagram!)

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.  This helps keep the content on the site free and I appreciate the support! :o)

TOOLS AND SUPPLIES

I used the following tools and supplies to create pixel Lakitu and Koopa Troopa.

TOOLS

• Jigsaw or a bandsaw
• Orbital Sander
• Router with 60 degree v-groove bit
• Clamp edge guide
• Kreg Mobile Project Center
• Ruler

SUPPLIES

• 2′ x 2′ plywood – 1/2″ thick
• Acrylic craft paints (white, kelly green and spice tan)
• Primer spray paint
• Clear coat
• Sand paper

WATCH THE VIDEO TUTORIAL

Click play and watch the video tutorial below.  The video shows how I made pixel Link, but the general steps remain the same for pixel Lakitu and Koopa Troopa. For more woodworking videos, CLICK HERE to subscribe to my YouTube channel.

Continue reading for the written tutorial.

HOW TO MAKE 8-BIT PIXEL
Lakitu and Koopa Troopa IN 5 EASY STEPS

1. Draw 1.5″ grid lines
2. Route along the grid lines
3. Cut out Lakitu’s and Koopa Troopa’s silhouette
4. Prep Pixel Lakitu and Koopa Troopa for painting
5. Paint Pixel Lakitu and Koopa Troopa

STEP 1: DRAW 1.5″ GRID LINES

Use a ruler to mark grid lines space 0.75″ apart.

STEP 2: ROUTE ALONG THE GRID LINES

Install a v-groove router bit and route along the grid lines. Use a clamp edge guide to ensure straight lines.

STEP 3: CUT OUT LAKITU’S AND KOOPA TROOPA’S SILHOUETTE

Cut out the Lakitu’s and Koopa Troopa’s shape with a jigsaw (or use a bandsaw).

STEP 4: PREP PIXEL LAKITU AND KOOPA TROOPA FOR PAINTING

Sand between the grooves and sand the surface of Lakitu and Koopa.  I used scrap piece of wood to support the sandpaper as I sanded between the grooves.

STEP 5: PAINT PIXEL LAKITU AND KOOPA TROOPA

Paint each pixel on Koopa Troopa and Lakitu. Painting between the grooves is a little tricky. Use painters tape to maintain clean lines. I was impatient and used paint brushes for painting miniatures to paint in the crevices.

If necessary, apply multiple layers of paint. Once the paint is dried, protect the finish with a clear coat.

The nice thing about working on Lakitu and Koopa Troopa at the same time is the characters use the exact same colors.

DIY 8-BIT PIXEL KOOPA TROOPA AND LAKITU

I am really happy with how the 8-bit Super Mario characters turned out. Next up: Spiny!

PIN IT!

FOLLOW ME on Pinterest.

The post 8-bit Lakitu and Koopa Troopa | Super Mario Bros. Pixel Art Tutorial appeared first on Handmade with Ashley.

Hello everyone, in this tutorial I’m sharing how to make an 8-bit end grain Goomba! This was a scrap wood project I made using remains from my Tardis end grain cutting board. I held onto the leftovers from that project for over a year. I could not bring myself to toss them out.

Let’s get started with the tutorial!

CLICK HERE to view more geeky and nerdy DIY projects.

Related Posts:

• 8-bit Blooper (Super Mario Bros.)
• 8-bit Goomba (Super Mario Bros.)
• 8-bit Lakitu and Koopa Troopa (Super Mario Bros)
• 8-bit Link (The Legend of Zelda)
• 8-bit Cheep Cheep (Super Mario Bros.)
• 8-bit Mario (Super Mario Bros.)

(For sneak peeks on upcoming projects follow me on Instagram!)

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.  This helps keep the content on the site free and I appreciate the support! :o)

Tools and Supplies

The following items are some of the tools and supplies I used to create end grain Goomba

Tools

• Bandsaw
• Orbital Sander
• Drum Sander

Supplies

• Walnut
• Cherry
• Maple
• 1/4″ Plywood
• Wood Glue
• Howard Butcher Block Conditioner

WATCH THE VIDEO TUTORIAL

Click play and watch the video tutorial below. For more woodworking videos, CLICK HERE to subscribe to my YouTube channel.

Continue reading for the written tutorial.

How to make 8-bit End Grain Goomba

End grain Goomba is my second 8-bit Goomba project. I’ve previously made a large pixel Goomba from 1/2″ plywood. CLICK HERE to read the tutorial on my original Goomba project.

This project I created using leftover pieces 3/4″ x 3/4″ x 2″ wood from my Tardis end grain cutting board project.

Step 1: Cut wood into 1/8″ thick squares

Cut the scrap walnut, maple and cherry into 1/8″ thick squares. I made these cuts on the bandsaw.

However, if I was not working with scrap wood I would have made most of my cut on the table saw.

For 8-bit Goomba you’ll need:

• 52 walnut squares
• 42 maple squares
• 96 cherry squares

Step 2: Glue wooden squares to plywood backer

Use wood glue to secure the wooden squares to a piece of 1/4″ plywood. I used my previous Goomba project as a pixel grid guide.

Step 3: Sand Goomba

View this post on Instagram

Just cleaned up Goomba’s surface. (I passed him through the drum sander multiple times between the first and last shot. ) Next, I’ll cut out his silhouette on the bandsaw. . #goomba #8bitgoomba #8bitsupermario #supermariobros #pixelart #geekcraft #geekdiy #videogamegeek #walnut #maple #cherry #drumsander #supermaxtools #supermaxdrumsanders #woodwork #woodworker #woodworking #makersgonnamake

A post shared by Ashley Grenon | Geeky Maker (@handmadewithashley) on Oct 8, 2018 at 1:22pm PDT

Sand Goomba. I used my drum sander to make quick work of the task.

Step 4: Cut out Goomba’s shape

Use a jigsaw or bandsaw to cut out Goomba’s shape.

View this post on Instagram

Cutting out most of Goomba’s shape on the bandsaw. The few tight areas I’ll cut out on the scroll saw. I noticed a few gaps so I guess next I’ll figure out a way to conceal my alignment errors. . #bandsaw #grizzlybandsaw #timelapse #lagunaresawking #grizzlyindustrial @grizzlyindustrial #mfpbehindthescenes #grizzlytools #g0555lx #goomba #pixelgoomba #8bitgoomba #rockler #dustright #woodwork #maker #geekcraft #geekdiy #woodworker #woodworking

A post shared by Ashley Grenon | Geeky Maker (@handmadewithashley) on Oct 8, 2018 at 1:55pm PDT

Step 5: Apply a finish and enjoy!

I used a beeswax and mineral oil mixture to finish Goomba. I installed a couple magnets on the backside to hang it on my garage door.

8-Bit End Grain Goomba | Super Mario Bros

Despite a few flaws, I’m pretty happy with how Goomba turned out. From a distance it’s hard to notice the mistakes (alignment issues).

Thanks for checking out my project! I hope it inspires you to create some 8-bit decor!

The post 8-bit End Grain Goomba | Super Mario Bros Pixel Art appeared first on Handmade with Ashley.

Hello everyone, in this post I’m sharing details about my latest 3D print: a quest marker for The Elder Scrolls: Skyrim. This was a project I started for February’s Art of Geek Challenge.

3D Model

When I first thought of the project, I had considered designing the model myself as an exercise for learning Fusion 360. But time ran out and fortunately I didn’t have to reinvent the wheel. I found the model for the Skyrim quest marker on Thingiverse. The model is designed by the user
Chronotau.

Companion 3D Print YouTube Video

Print Time

This was a short print. It took roughly 4 hours for the outer portion and another 2 hours for the inner portion. I printed the model at 20% infill with a brim on my Prusa i3 MK2S 3D printer.

Filament

I printed the outer portion of the quest marker in Black PLA from Atomic Filament. The inner portion of the marker was printed in White PETG from Atomic Filament. (It was the only white filament I had on hand, otherwise I would have used PLA.)

Assembly

The model was well designed and the two pieces snapped together. There is a slot in the model so no worries about alignment. I added a little super glue to keep the two pieces secured together.

3D Printed Skyrim Quest Marker

This was a fun print and I’ll hang the quest marker up in my garage.

The post 3D Printed Skyrim Quest Marker | The Elder Scrolls appeared first on Handmade with Ashley.

Hello everyone, today I’m sharing how to make 8-bit pixel Blooper from the NES version of Super Mario Bros. I created this project on a whim when I noticed I had a scrap piece of 1/2″ plywood sitting on my garage floor. I followed the same technique I used to create 8-bit pixel Link from the original The Legend of Zelda game.

CLICK HERE to view more geeky and nerdy DIY projects.

Related Posts:

• 8-bit Goomba (Super Mario Bros.)
• 8-bit End Grain Goomba (Super Mario Bros.)
• 8-bit Link (The Legend of Zelda)
• 8-bit Cheep Cheep (Super Mario Bros.)
• 8-bit Mario (Super Mario Bros.)
• 8-bit Lakitu and Koopa Troopa (Super Mario Bros)

(For sneak peeks on upcoming projects follow me on Instagram!)

Disclosure: This post contains affiliate links.  That means if you purchase an item via one of these links, I’ll receive a small commission at no added cost to you.  This helps keep the content on the site free and I appreciate the support! :o)

Tools and Supplies

I used the following tools and supplies to create pixel Blooper.

Tools

• Jigsaw or a bandsaw
• Orbital Sander
• Router with 60 degree v-groove bit
• Clamp edge guide
• Kreg Mobile Project Center
• Ruler

Supplies

• 2′ x 2′ plywood – 1/2″ thick
• Acrylic craft paints (black, gray, and white)
• Primer spray paint
• Clear coat
• Sand paper

Watch the video tutorial

Click play and watch the video tutorial below.  The video shows how I made pixel Link, but the general steps remain the same for pixel Blooper. For more woodworking videos, CLICK HERE to subscribe to my YouTube channel.

Continue reading for the written tutorial.

How to make 8-bit pixel Blooper in 5 easy steps

1. Draw 1.5″ grid lines
2. Route along the grid lines
3. Cut out Blooper’s silhouette
4. Prep Pixel Blooper for painting
5. Paint Pixel Blooper

Step 1: Draw 1.5″ grid lines

Use a ruler to mark grid lines space 1.5″ apart.

Step 2: Route along the grid lines

Install a v-groove router bit and route along the grid lines. Use a clamp edge guide to ensure straight lines.

Step 3: Cut out Blooper’s silhouette

Cut out the Blooper’s shape with a jigsaw (or use a bandsaw).

Step 4: Prep Pixel Blooper for painting

Sand between the grooves and sand the surface of Blooper.  I used scrap piece of wood to support the sandpaper as I sanded between the grooves.

Step 5: Paint Pixel Blooper

Paint each pixel on Blooper. Painting between the grooves is a little tricky. Use painters tape to maintain clean lines. I was impatient and used paint brushes for painting miniatures to paint in the crevices.

If necessary, apply multiple layers of paint. Once the paint is dried, protect the finish with a clear coat.

DIY 8-Bit Pixel Blooper

I am really happy with how pixel Blooper turned out.

PIN IT!

FOLLOW ME on Pinterest.

The post 8-Bit Blooper | Super Mario Bros NES Pixel Wall Art Tutorial appeared first on Handmade with Ashley.

Hello everyone, today I’m sharing a really cool 3D print of Thanos! The Thanos model was designed by David Östman and is available for download via My Mini Factory.

RELATED POSTS:

• 3D Printed Darth Vader Bust
• 3D Printed Stan Lee Memorial Bust

The bust took about 19 hours to print at 5% infill and with no supports.
I printed the model with PolyAlchemy’s Onyx Elixir PLA and love how it came out.

This is a really cool model, and I look forward to printing more of Mr. Östman‘s work!

The post Thanos Bust | 3D Printing appeared first on Handmade with Ashley.

A 3D printed bust of one of the greatest villains of all time: Darth Vader. (3D model designed by David Östman)

Hello everyone, today I’m sharing one my of favorite 3D prints so far: a bust of the Star Wars villain, Darth Vader! The Darth Vader model was designed by David Östman and is available for download via My Mini Factory.

RELATED POSTS:

• Darth Vader resin necklace
• Star Wars TIE Fighter Bookshelf
• Star Wars Marquee Sign
• 3D Printed Stan Lee Bust

The model is split into two parts: the bust and the stand. No supports are required.

I printed the model with PolyAlchemy’s Onyx Elixir PLA and wow! That stuff looks incredible.

The bust took roughly 26 hours to print and the stand was another 8 hours or so. I printed it at 20% infill.

The first attempt at printing the model, I tried printing it at 0% infill. Unfortunately, it failed. I think probably because the Elixir filament is a bit flexible and and some point during the print it flexed and triggered a chain reaction of fail.

This is a wonderful model, and I can’t wait to print more of Mr. Östman‘s work!

The post Darth Vader Bust | 3D Printing appeared first on Handmade with Ashley.